SKATE BOARD STOOL KIT
This is a nice part that allows you to turn your skateboard into a stool by attaching this part instead of attaching trucks to the 4 holes (2 places) on the skateboard deck. The best feature is that you can attach and detach the 4 legs with magnets. It is also nice to be able to carry it compactly with the detached legs held in the holder on the back of the board. It has a wide range of uses from indoor to outdoor.
We recommend it not only as a chair or table for camping and outdoor activities, but also as an additional chair for guests, store fixtures, display stands, and TV racks. You can also use it as a bench for two childs.
The skateboard is not very wide (deep), so it can be placed against a wall in a small room without reducing the floor space. They are thin enough to be stored in a small space, and even if you own a lot of skateboards, you can stack them on top of each other and they will not take up more space than the width of the deck. Even with the legs folded (legs stored on the back), the ground surface is flat, so it can be used as an ultra-low table.
The holes are also compatible with old decks from the 80's. The strength of this product has been carefully calculated.
You can use it for your collection, or for your favorite deck which is too good to ride, and you can use it as a practical product.
Please prepare the skateboard deck of your choice.
It is strong enough to stand on, and the skateboard top is long enough so that you can step on it with stability. It can also be used as a stepladder (step ladder) when picking up high objects or when unloading items from the roof rack of your car. It also looks smart when placed in the cargo area of a car.
Please do not jump on the top board and do not shake it forcibly.
It can be used as a small side table as well.
You can also use it as a two-tier rack by placing the first tier on the floor if the board is less than 8 inches (about 20cm), which fits in the width of the leg opening.
- Size: Seat height: 40 cm (assuming a deck thickness of 10 mm)
Thickness of the parts when stored: 45mm
- Material: Nylon resin with glass fiber (resin molded parts), BLACK electroplated coating made of duralumin (leg pipe), BLACK electroplated coating made of steel (attached countersunk screws) (*This product is designed for particular use.) Neodymium magnet (magnet)
- Compatible size
Compatible with a board thickness of 11mm or less, foil base (hole to hole inside) 350mm to 400mm. In case of more than that, you can use it without using the "Pole Holder". (In that case, please carry the 4 leg parts separately).
If you have a deck with a short nose and long tail, the position of the legs will be offset considerably. Please pay attention to the seating position when seated. Some decks may not be able to be joined properly depending on the position of the concave (warp of the board).
Please be aware that there is a slight gap between the leg pipe and the insert, which is necessary for structural reasons.
If the countersunk screws are too shallow, do not tighten them forcibly; instead, carve the holes in the deck at a 90-degree angle to make the screw heads flat. (If you turn the screw forcibly, it may damage the Phillips screw head or the parts or the deck.
The bit for seat engraving looks like this.
https://www.amazon.co.jp/gp/product/B001WHEM54/ref=ppx_yo_dt_b_asin_title_o02__o00_s01?ie=UTF8&psc=1 ( Search word: Star-M HSS Hexagonal Chamfering Cutter NO.5007 8MM)
Please pay attention to the degree of penetration of the legs when assembling, the unevenness of the installation surface, and the distance from vehicles and walls when using it as a stepladder.
This product contains a powerful magnet, so please keep away from objects that may cause problems due to magnetism. (e.g., cards, precision instruments, recording media, PC-related products, watches, etc.)
- Quantity: 1
- Item number: 115649